Belt Washer / Oven For Sale       

CINCINNATI INDUSTRIAL MACHINERY BELT TYPE, GAS, CONTINUOUS FEED WASHER/OVEN     Item # PC 10042

Opening - 72" wide x 48" high

Belt speed - 5  FPM

Belt drive - Morse Md.406GCDB-RL-145T gear reducer drive, Ratio 125:1, Sn- K96MP07588, w/Baldor  2hp/208/230/460v/60cy/1750 rpm, driving a 12" top sprocket

Belt – Ashworth C1x1

Belt controls - Start/stop, E-stop, electric photo eye on/off

Belt capacity - 5,000#/hour at present feed speeds

Washer tank, constructed of ¼” MS

            Insulated with 2” thick mineral wool insulation w/20 gauge MS cover

            1500 gallon capacity, 15.5’ long x 10.5’ wide x 2.5’ high. Fluid level is 21”

            (6) sets of nozzles, 4-high on Left & right, 6-across on top & bottom

            Pump @ 450 gpm @ 40' head

            Temperature - 160 degrees Fahrenheit

            Part time in washer - 60 seconds

            Dimensions - 13' tall x 8' wide

Rinse tank – ¼” mild steel

            750 gallon capacity

            Nozzles - (4) sets, 4-high left & right, 6-across top & bottom

            Pump @ 250 gpm @ 40' head

            Part time in rinse - 30 seconds

Nozzles - (204) Plastic clip-ons, type 6550 V-jets

Oven - 300 degrees Fahrenheit, 24' long, plus a 12' long "unload" extension.

            Dimensions - 13'2" high x 8' wide

Natural gas @ 15 psi

Controls - PLC

Main - Washer pump on/off, #1 Air seal on/off, Entry vent on/off, #2 Air seal on/off, Exit vent on/off, Washer heater burner on/off, Conveyor on/off, Oven exchanger on/off, Oven recirculate on/off, Oven burner blower on/off

DT1 - Wash heat temp controls @ 160 degrees max., Wash pilot on/off, Wash

heat safety lights - Green = OK, for Wash heat burner

DT2 - Oven burner temp controls @ 300 degrees max., Orange light for Oven burner purging, Green light for Oven burner purged, Oven pilot on/off/stop,

Oven burner Green light = ON

Preheat Auto Start Timer for washer by Intermatic, AM/PM, manual/auto, etc.

Overall length - Approximately 78' overall, but can be reduced by 7' on the exit side & 12' on the entrance side, which still allows for a "dead loading & unloading" area within the washer & the oven for parts.

Washer consists of – 7’ extension from washer housing, 7’ approach to dual wash stages (inside washer), 10’ of drain, 2’6” of rinse, 7’ of drain. There is approximately 4’ of a dead zone between the washer and the oven. It was originally shipped as 32’8” for the washer & 7’ for the “extension”, plus the oven and it’s extension.

Equipped   With overhead lifting eyes on both washer & oven for easy removal

Condition:   Excellent

Housings    Made of  11 ga. Aluminized steel

Note: Speeds can be increased by either going to a 40:1, 50:1, or 60:1 gear box, with pricing ranging from $880.00 to $1,006.00 OR put a Potentiometer control on it for a full range of speeds.

Year Built - 1997 (SN-B-128-C21)                                                                                                       

Replacement cost - $300,000.00

Item ID #           PC 10042

Contact

	Paul J Kendzor
Phone	(570) 262-5713
Fax	(570) 603-7438
Email	Sales@Kendzor.com